Nissan Maxima: Changing a flat tire - In case of emergency - Nissan Maxima Owners ManualNissan Maxima: Changing a flat tire

If you have a flat tire, follow the instructions below:

Stopping the vehicle

1. Safely move the vehicle off the road and away from traffic.

2. Turn on the hazard warning flashers.

3. Park on a level surface and apply the parking brake. Move the shift selector to P (Park).

4. Turn off the engine.

5. Raise the hood to warn other traffic and to signal professional road assistance personnel that you need assistance.

6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.

WARNING:

- Make sure the parking brake is securely applied and the CVT is shifted into P (Park).

- Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.

- Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance.

 Blocking wheels
 Blocking wheels

Place suitable blocks (1) at both the front and back of the wheel diagonally opposite the flat tire  (2)- to prevent the vehicle from moving when it is jacked up.

WARNING:

Be sure to block the wheel as the vehicle may move and result in personal injury.

 Type A
 Type A

Getting the spare tire and tools

Open the trunk. Remove the floor carpeting.

 Type B
 Type B

 Type A
 Type A

 Type B
 Type B

Lift the spare tire cover.

Remove the jack (1) and wheel nut wrench (2)- from the tool box on the right

Remove the jack (1) and wheel nut wrench (2)- from the tool box on the right side of the trunk compartment.

Remove the spare tire.

Remove the spare tire.

 Jacking up vehicle
 Jacking up vehicle and removing the damaged tire

WARNING:

- Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands.

- Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change.

- Use the correct jack-up points. Never use any other part of the vehicle for jack support.

- Never jack up the vehicle more than necessary.

- Never use blocks on or under the jack.

- Do not start or run the engine while vehicle is on the jack. It may cause the vehicle to move. This is especially true for vehicles with limited slip differentials.

- Do not allow passengers to stay in the vehicle while it is on the jack.

- Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move.

Always refer to the proper illustrations for the correct placement and jack-up

Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type.

Carefully read the caution label attached to the jack body and the following instructions.

1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.

2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point.

Align the jack head between the two notches in the front or the rear as shown.

Also fit the groove of the jack head between the notches as shown.

The jack should be used on firm and level ground.

3. To lift the vehicle, securely hold the jack lever and rod with both hands. Carefully raise the vehicle until the tire clears the ground. Remove the wheel nuts, and then remove the tire.

 Installing the
 Installing the spare tire

The spare tire is designed for emergency use. See specific instructions under the heading Wheels and tires in the Maintenance and do-it-yourself section of this manual.

1. Clean any mud or dirt from the surface between the wheel and hub.

2. Carefully put the spare tire on and tighten the wheel nuts finger tight.

3. With the wheel nut wrench, tighten wheel nuts alternately and evenly as illustrated until they are tight.

4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated ( (A) , (B)- , (C)- , (D)- , (E)- ). Lower the vehicle completely.

WARNING:

- Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off.

This could cause an accident.

- Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.

- Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.

Wheel nut tightening torque:

83 ft-lb (112 N·m) The wheel nuts must be kept tightened to specification at all times. It is recommended that wheel nuts be tightened to specifications at each lubrication interval.

Adjust tire pressure to the COLD pressure.

COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km).

COLD tire pressures are shown on the Tire and Loading Information label affixed to the drivers door opening.

5. Securely store the flat tire and jacking equipment in the vehicle.

6. Place the spare tire cover and the trunk floor carpeting over the damaged tire.

7. Close the trunk.

WARNING:

- Always make sure that the spare tire and jacking equipment are properly secured after use. Such items can become dangerous projectiles in an accident or sudden stop.

- The spare tire is designed for emergency use. See specific instructions under the heading Wheels and tires in the Maintenance and do-it-yourself section of this manual.

    Tire Pressure Monitoring System (TPMS)
    This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of y ...

    Jump starting
    To start your engine with a booster battery, the instructions and precautions below must be followed. WARNING: - If done incorrectly, jump starting can lead to a battery explosion, resulting in ...

    See also:

    How Your Front Airbags Work
    If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration. If the rate of deceleration is high enough, the control unit will inflate ...

    Seat belt maintenance
    -To clean the seat belt webbing, apply a mild soap solution or any solution recommended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do no ...

    Tire Identification Number (TIN)
    Tire Identification Number (TIN) is marked on the intended outboard sidewall. The TIN is composed of four groups. Here is a brief review of the TIN with a breakdown of its individual elements. ...