Toyota Camry: Power windows
The power windows can be opened and closed using the switches.
Operating the switch moves the windows as follows:
1 Closing
2 One-touch closing (driver’s window only)*
3 Opening
4 One-touch opening (driver’s window only)*
*: Pressing the switch in the opposite direction will stop window travel partway.
Window lock switch
Press the switch down to lock the passenger window switches.
Use this switch to prevent children from accidentally opening or closing a passenger window.
■The power windows can be operated when
Vehicles without a smart key system
The engine switch is in the “ON” position.
Vehicles with a smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
■Operating the power windows after turning the engine off
Vehicles without a smart key system
The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, however, be operated once either front door is opened.
Vehicles with a smart key system
The power windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.
■Jam protection function (driver’s window only)
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
■When the power window does not close normally (driver’s window only)
If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the driver’s door.
●Vehicles without a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position.
●Vehicles with a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the “ENGINE START STOP” switch is turned to IGNITION ON mode.
●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following procedure.
- Hold the power window switch in the one-touch closing position.
Continue holding the switch for a further 6 seconds after the window has closed. - Hold the power window switch in the one-touch opening position.
Continue holding the switch for a further 2 seconds after the window has opened completely. - Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
If you release the switch while the window is moving, start again from the beginning.
If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
■Customization that can be configured at Toyota dealer
Settings (e.g. key linked operation) can be changed.
(Customizable features)
CAUTION
■Closing the windows
Observe the following precautions.
Failure to do so may result in death or serious injury.
●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●Do not allow children to operate the power windows.
Closing a power window on someone can cause serious injury, and in
some instances, even death.
■Jam protection function (driver’s window only)
●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just
before the window fully closes.
Moon roof
Use the overhead switches to open and close the moon roof and tilt it up and down. Opening and closing 1 Opens the moon roof* The moon roof stops slightly before the fully open position to ...See also:
Reference
This chapter contains technical data, short
commands for the voice activation system, and an
index that will quickly take you to the information
you need. ...
Ultrasonic Parking Assist
If available, Ultrasonic Rear Parking
Assist (URPA) system uses sensors
on the rear bumper to assist with
parking and avoiding objects while
in R (Reverse). It operates at
speeds less than 8 ...
Safety Certification
FCC ID: CB2MBLUEC07 IC:279BMBLUEC07.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:
(1) This device m ...