Hyundai Sonata: To set cruise control speed - Cruise control system - Driving your vehicle - Hyundai Sonata Owners ManualHyundai Sonata: To set cruise control speed

1. Push the cruise ON-OFF button on the steering wheel to turn the system on. The CRUISE indicator light in the instrument cluster will illuminate.

2. Accelerate to the desired speed, which must be more than 25 mph (40 km/h).

3. Push the SET- switch, and release it at the desired speed. The SET indicator

3. Push the SET- switch, and release it at the desired speed. The SET indicator light in the instrument cluster will illuminate. Release the accelerator at the same time. The desired speed will automatically be maintained.

On a steep grade, the vehicle may slow down or speed up slightly while going uphill or downhill.

To increase cruise control set speed:

To increase cruise control set speed:

Follow either of these procedures:

• Push the RES+ switch and hold it. Your vehicle will accelerate. Release the switch at the speed you want.

• Push the RES+ switch and release it immediately. The cruising speed will increase 1.0 mph (1.6 km/h) each time the RES+ switch is operated in this manner.

To decrease the cruising speed: Follow either of these procedures:

To decrease the cruising speed: Follow either of these procedures:

• Push the SET- switch and hold it. Your vehicle will gradually slow down. Release the switch at the speed you want to maintain.

• Push the SET- switch and release it immediately. The cruising speed will decrease 1.0 mph (1.6 km/h) each time the SET- switch is operated in this manner.

To temporarily accelerate with the cruise control on:

If you want to speed up temporarily when the cruise control is on, depress the accelerator pedal. Increased speed will not interfere with cruise control operation or change the set speed.

To return to the set speed, take your foot off the accelerator.

To cancel cruise control, do one of the following:

To cancel cruise control, do one of the following:
• Press the brake pedal.
• Press the clutch pedal with a manual transaxle.
• Shift the shift lever into N (Neutral) with an automatic transaxle
• Press the CANCEL switch located on the steering wheel.
• Decrease the vehicle speed lower than the memory speed by 9 mph (15 km/h).
• Decrease the vehicle speed to less than approximately 25 mph (40 km/h).

Each of these actions will cancel cruise control operation (the SET indicator light in the instrument cluster will go off), but it will not turn the system off. If you wish to resume cruise control operation, push the RES+ switch located on your steering wheel. You will return to your previously preset speed.

To resume cruising speed at more than approximately 25 mph (40 km/h):

To resume cruising speed at more than approximately 25 mph (40 km/h):

If any method other than the cruise ON/OFF switch was used to cancel cruising speed and the system is still activated, the most recent set speed will automatically resume when the RES+ switch is pushed.

It will not resume, however, if the vehicle speed has dropped below approximately 25 mph (40 km/h).

NOTICE

Always check the road conditions when pressing the RES+ switch to resume the speed.

To turn cruise control off, do one of the following:

To turn cruise control off, do one of the following:

• Push the cruise ON/OFF button (the CRUISE indicator light in the instrument cluster will go off).
• Turn the ignition off.
Both of these actions cancel cruise control operation. If you want to resume cruise control operation, repeat the steps provided in “To set cruise control speed” on the previous page.

    Cruise control system
    1 CRUISE indicator 2 SET indicator The cruise control system allows you to program the vehicle to maintain a constant speed without resting your foot on the accelerator pedal. This system is des ...

    Economical operation
    Your vehicle's fuel economy depends mainly on your style of driving, where you drive and when you drive. Each of these factors affects how many miles (kilometers) you can get from a gallon (l ...

    See also:

    Transmission control system warning
    If the “AT OIL TEMP” warning light flashes after the engine has started, it may indicate that the transmission control system is not working properly. Contact your nearest SUBARU dealer for se ...

    EPB Release
    To release the EPB, place the ignition in the ON/RUN position, apply and hold the brake pedal, and push down momentarily on the EPB switch. If you attempt to release the EPB without the brak ...

    Important safety notes
    The rear view camera is an optical parking aid. It shows the area behind your vehicle in the COMAND display. WARNING Make sure that no persons or animals are in the maneuvering range. Other ...