Buick LaCrosse: UHP Controls - Bluetooth (UHP Mexico Only) - Phone - Infotainment System - Buick LaCrosse Owners ManualBuick LaCrosse: UHP Controls

Use the buttons located on the infotainment system and the steering wheel to operate the UHP system.

Steering Wheel Controls

Steering wheel controls can be used to:
• Answer incoming calls
• Confirm system information
• Start voice recognition
• End a call
• Reject a call
• Cancel an operation
• Make outgoing calls using the call list

answer incoming calls, to confirm (Push To Talk) : Press to answer incoming calls, to confirm system information, and to start voice control. Press and hold for two to three seconds to access the call list.

end a call, reject a call, or to cancel (End call/Mute) : Press to end a call, reject a call, or to cancel an operation.

To make outgoing calls using the call list.

1. Press the 2. Highlight the phone number by button.

2. Highlight the phone number by toggling the SRC switch up or down.

3. Dial the highlighted number by pressing the Infotainment System Controls button.

Infotainment System Controls

For information about how to navigate the menu system using the navigation system controls, see the separate Navigation System Manual.

PHONE : Press to enter the Phone main menu.

Voice Control

The voice control system uses commands to control the system and dial phone numbers.

Noise: The system may not recognize voice commands if there is too much background noise.

When to Speak: A tone sounds to indicate that the system is ready for a voice command. Wait for the tone and then speak.

How to Speak: Speak clearly in a calm and natural voice.

Audio System

When using the UHP system, sound comes through the vehicle's front audio system speakers and overrides the audio system. Use the VOL/ O knob during a call to change the volume level. The adjusted volume level remains in memory for later calls. The system maintains a minimum volume level.

Turning Bluetooth On or Off

1. Press the CONFIG button.

2. Select Phone Settings, or touch Phone on a navigation radio.

3. Select Bluetooth.

4. Select Activation.

Changing Bluetooth Code

The default Bluetooth code should work with most mobile phones.

If you are having difficulty pairing your mobile phone, you can change the code at any time.

1. Press the CONFIG button.

2. Select Phone Settings, or touch Phone on a navigation radio.

3. Select Bluetooth.

4. Select Change Bluetooth Code.

5. Enter a new four-digit code, then select OK.

Ring Tone

There are three different ring tones available for the UHP system.

To change the ring tone:

1. Press the CONFIG button.

2. Select Phone Settings, or touch Phone on a navigation radio.

3. Select Ring Tones.

4. Select Ring Tone 1, 2, or 3.

Default Settings

Selecting this option will reset the ring tones and the Bluetooth code.

    Other Information
    The Bluetooth word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their resp ...

    Pairing
    A Bluetooth enabled mobile phone must be paired to the UHP system first and then connected to the vehicle before it can be used. See the mobile phone manufacturer's user guide for Bluetooth ...

    See also:

    Supplemental Restraint Systems (SRS) Precautions
    The front and side supplemental restraint systems (SRS) include 6 air bags. You can locate the various air bags by the use of “SRS AIRBAG” location indicators. These indicators are visible in t ...

    112,500 miles (180,000 km) or 90 months
    ❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect manual transaxle fluid (if equipped) ❑ Replace engine oil and filter (112,500 miles (180,000 km) or 180 mont ...

    Windshield wipers
    MIST : Mist (for a single wipe) OFF : Off INT: Intermittent LO: Low speed HI: High speed To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to t ...