Mercedes-Benz E-Class: Windshield wipers

Intermittent wiping with rain sensor: due to optical influences and the windshield becoming dirty in dry weather conditions, the windshield wipers may be activated inadvertently. This could then damage the windshield wiper blades or scratch the windshield.

For this reason, you should always switch off the windshield wipers in dry weather.

In the or position, the appropriate wiping frequency is set automatically according to the intensity of the rain. In the position, the rain sensor is more sensitive than in the position, causing the windshield wipers to wipe more frequently.

Switching the rear window wiper on/ off

Combination switch

1. Switch
2. To wipe with washer fluid
3. I To switch on intermittent wiping
4. 0 To switch off intermittent wiping
5. To wipe with washer fluid

•► Turn the SmartKey to position 1 or 2 in the ignition lock.

•► Turn switch 1 on the combination switch to the corresponding position.

When the rear window wiper is switched on, the icon appears in the instrument cluster.

Replacing the wiper blades

Important safety notes

WARNING
For safety reasons, switch off the windshield wipers and remove the key from the ignition lock before changing the wiper blades (vehicles with KEYLESS-GO: make sure that the on-board electronics are in state 0).

Otherwise, the wiper motor could be switched on suddenly and cause injury.

To avoid damaging the wiper blades, make sure that you touch only the wiper arm of the wiper.

Never open the hood if a windshield wiper arm has been folded away from the windshield.

Never fold a windshield wiper arm without a wiper blade back onto the windshield/ rear window.

Hold the windshield wiper arm firmly when you change the wiper blade. If you release the windshield wiper arm without a wiper blade and it falls onto the windshield, the windshield may be damaged by the force of the impact.

Mercedes-Benz recommends that you have the wiper blades replaced by a qualified specialist workshop, e.g. at an authorized Mercedes-Benz Center.

Replacing the windshield wiper blades

Removing the wiper blades

•► Remove the SmartKey from the ignition lock or turn it to position 0 (KEYLESS-GO).

•► Fold the wiper arm away from the windshield until it engages.

•► Set the wiper blade at right angles to the wiper arm.

•► Remove the wiper blade from the retaining pin on the wiper arm in the direction of the arrow.

Installing the wiper blades

•► Push the new wiper blade onto the retaining pin on the wiper arm in the opposite direction to the arrow.

Make sure that the wiper blade slides fully onto the retaining pin on the wiper arm.

•► Turn the wiper blade parallel to the wiper arm.

•► Fold the wiper arm back onto the windshield.

Replacing the rear window wiper blade

Removing the wiper blade

•► Remove the SmartKey from the ignition lock.

•► Fold wiper arm 1 away from the rear window until it engages.

•► Position wiper blade 2 at a right angle to wiper arm 1.

•► Hold wiper arm 1 and press wiper blade 2 in the direction of the arrow until it releases.

•► Remove wiper blade 2.

Installing the wiper blade

•► Place new wiper blade 2 onto wiper arm 1.

•► Hold wiper arm 1 and press wiper blade 2 in the opposite direction to the arrow until it engages.

•► Make sure that wiper blade 2 is seated correctly.

•► Position wiper blade 2 parallel to wiper arm 1.

•► Fold wiper arm 1 back onto the rear window.

Problems with the windshield wipers

The windshield wipers are obstructed

Leaves or snow, for example, may be obstructing the windshield wiper movement.

The wiper motor has been deactivated.

•► For safety reasons, you should remove the SmartKey from the ignition lock.
or
•► Switch off the engine using the Start/Stop button and open the driver's door.

•► Remove the cause of the obstruction.

•► Switch the windshield wipers back on.

The windshield wipers are inoperative

The windshield wiper drive is malfunctioning.

•► Select another wiper speed on the combination switch.

•► Have the windshield wipers checked at a qualified specialist workshop.

The spray nozzles are misaligned

The windshield washer fluid from the spray nozzles no longer hits the center of the windshield. The spray nozzles are misaligned.

•► Have the spray nozzles adjusted at a qualified specialist workshop.

Replacing bulbsUseful information